Our own precision balsa stripper. It uses standard single edge razor blades instead of the usual #11 blade. Cut width set by plastic spacers, 3 off 1/16", 1 each 1/32" and 1/64" included. Cut depth is adjustable.
Extra keen blade included.
|
Silicon based Rubber Lubricant
|
10g calibration weight for checking
digital scales.
|
Precise digital scale measures 0 - 300g
with a resolution of 0.01g.
A necessary tool for indoor rubber power.
|
9.5" Medium IFFS prop on hanger, blade color is now black.
This is the prop from Indoor Free Flight Supply company, it weighs ~2g. Can be trimmed to a smaller size with scissors!
|
2025/2026 Helicopter Kit.
Kit makes 3 complete Helicopters.
Rotor diameter ~33.2 cm (13"), length 40.2 cm. (16")
Comes with two rotor building jigs, enough rubber for 6 motors, "o" rings, 3D Printed prop hub & hanger and carbon rods.
|
5 Nose buttons for 0.020" prop shaft.
(Fits all loop hangers.)
|
5 Nose buttons for 0.026" prop shaft.
(Fits all loop hangers.)
|
5 Nose buttons for 0.032" prop shaft.
(Fits all loop hangers.)
|
Hanger loop for 1/8" motor sticks, nose button for 0.020" prop shaft. Three sets included. Glue hanger loop to motor stick with CA.
This allows you to easily change out prop and shaft assembly on your stick models.
|
Hanger loop for 1/8" motor sticks, nose button for 0.026" prop shaft. Three sets included. Glue hanger loop to motor stick with CA.
This allows you to easily change out prop and shaft assembly on your stick models.
|
Hanger loop for 1/8" motor sticks, nose button for 0.032" prop shaft. Three sets included. Glue hanger loop to motor stick with CA.
This allows you to easily change out prop and shaft assembly on your stick models.
|
Hanger loop for 1/8" motor sticks, nose button for 0.020" prop shaft, prop hub for 1.0mm carbon rods and two thrust washers. Prop shaft, thrust washers and carbon rods not included.
|
Hanger loop for 1/8" motor sticks, nose button for 0.026" prop shaft, prop hub for 1.0mm carbon rods. Prop shaft, thrust washers and carbon rods not included.
|
Hanger loop for 1/8" motor sticks, nose button for 0.032" prop shaft, and prop hub for 1.0mm carbon rods. Prop shaft , thrust washers and carbon rods not included.
|
Torque meter kit, Carbon Fiber body tube, swivels to align with rubber. Approximate range 0 - 2 oz-in (0.014 N-m), suitable for up to 1 loop of 1/8" Super Sport.
|
Winder Box allows the student to set the winder down with a fully wound motor, leaving both hands free to transfer motor to the model. Key hole mount, simply use 1 pan head screw. Winder sold seperately.
|
Winder Box allows the student to set the winder down with a fully wound motor, leaving both hands free to transfer motor to the model. Key hole mount, simply use 1 pan head screw. Winder sold seperately.
|
3D Printed plastic box corners, 1.125" x 1.125" x 1.125".
They make it easy to construct a rectangular box from foam board or other rigid material.
|
15:1 winder, faster winding for long/thin motors
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #0 - 1/8" OD for 0.020" shaft
|
10:1 light duty winder, all plywood gears, a fun project with a functional winder once you are done.
|
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #1 - 1/8" OD for 1/32" shaft
|
Universal indoor model stand, ~9" tall for all stick fuselage type models, fixed wing and helicopters. Great for safely holding delicate Science Olympiad models.
|
6 off - 1/4" OD - 1/8" ID (No. 6) Buta-N O-Rings
|
6 off - #4 Buta-N O-Rings
|
6 off - 15/64" OD - 7/64" ID (No. 5) Buta-N O-Rings
|
Traditional boiled green soap and glycerene lube.
|
1/4" wide masking tape - 60yd roll
color may vary according to availability
|