1/16" - Use to help build a second identical fuselage frame over first frame. Set of 18.
|
1/8" - Use to help build a second identical fuselage frame over first frame. Set of 18.
|
3/32" - Use to help build a second identical fuselage frame over first frame. Set of 18.
|
Pair of 7.5mm OD carbon tubes 23" long. Use to build wing on, align fuselage building jigs and other jigs with alignment hole.
|
Pack of 50 0.25" x 0.10" high power rare earth magnets. Use for magnetic building jig system or as cowl/hatch retainers in your model.
|
Pack of 16 0.25" x 0.10" high power rare earth magnets.
|
Set of 16 fuselage jig supports, one each 1/8"....2" wide in steps of 1/8". Forks are 2" high. Laser cut from birch plywood. Use with 7.5mm OD carbon rod and/or magnets, both sold separately.
|
Individual fuselage supports, please specify width required in notes field at checkout.
Available in step of 1/16" from 1/8" - 2" wide. Forks are 2" high.
|
Big adjustable fuselage support, sold individually.
Adjusts from 1 1/2" to over 4 1/2" wide. Forks are 5" high. 7.5mm Carbon rod and magnets sold separately.
|
Unique tool rides on 7.5mm carbon rod used in your fuselage jig, and provides a 10" wide perpendicular ruler graduated in 1/8" from -5" to +5". Very useful for setting up wing and stabilizer square to fuselage.
|
Used to square up root rib when building wings on 7.5mm carbon rods. Laser cut from birch plywood.
|
Pack of four hold-down fingers. Lightly sprung to hold your thin sticks in place while you glue. Laser cut from birch plywood. Use with magnets (magnets sold separately).
|
Pack of two sets. These long fingers will hold light structures 1/8" off the board so tissue can evenly shrink warp free after steaming or doping tissue. Laser-cut from birch plywood. Use 6 1/4" x 0.100" magnets per pack,(magnets sold separately).
|
Pack of four hold-down fingers. Lightly sprung to hold your thin sticks in place while you glue. Laser cut from birch plywood. Use with magnets (magnets sold separately).
|
Pack of four 1/16" rib squares, 1" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of 4 3/32" rib squares, 1" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 1/8" rib squares, 1" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 1/16" rib squares, 2" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 3/32" rib squares, 2" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 1/8" rib squares, 2" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four (two inside & two outside) 30/90/60 deg squares. Longer edge of square edges is 2". Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pack of four (two inside & two outside) 45/90/45 deg squares. Square edges are 2" long. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Set of 8 double ended Dihedral angle jigs. (only 4 shown in photo). One deg. steps from 0 - 15 deg. angle. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Set of 2 keel support stands with 1/16" slot. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Can be used with carbon alignment rod.
|
Set of 2 keel support stands with 3/32" slot. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Can be used with carbon alignment rod.
|
Set of 2 keel support stands with 1/8" slot. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Can be used with carbon alignment rod.
|
Pack of two 5 1/4" tall squares. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of two 12" horizontal scales. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pack of two 6" tall vertical scales. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pair of wing/stabilizer support fixtures. Adjusts from 1" to 7" high, and angle tilts over the range of -7.5 to + 7.5 deg. Nylon bolts and wing nuts used to lock fixture after adjusting. For magnetic tables add 4 magnets to each fixture (not supplied).
|